Heavy Duty Heated Windshield Wipers - 56HC Series
Price:
$109.75
Compare At:
$120.00
View more items in
Heated Windshield Wipers
View more items from
Everblades
Heavy Duty (Five Bar) 1/8", 3/16" and 1/4" Saddle Mount. Sold in sets of two with a wiring harness, fuse, and switch.
For curved or flat windshields on some heavy duty trucks and some buses. (Mounts to wiper arm with a little screw and nut.) 12″, 14″, 15″, 16″, 18″ & 20″ lengths!
BEGIN INSTALLATION
1. Mount illuminated on/off switch in convenient dash or under-dash location.
2. Hook blue wire to GOOD ground.
3. Attach red wire to a switched circuit.
NOTE: A "switched" circuit is one that is OFF when the ignition is OFF. For example, if your switch is lit with the ignition OFF, the attachment is wrong.
4. Turn wiper switch and ignition "ON".
5. Check that the switch light is "ON" = system connected properly. NOTE: Power will be supplied to the heater elements only when the switch light is "ON".
6. Run black wire from switch through firewall of vehicle and secure wires.
NOTE: You have the option of running around the firewall.
• Remove existing wiper blade assemblies from wiper arms. NOTE: Keep old adapters until Everblades® are installed - they may be useful!
• Clean the windshield completely.
• Recommended cleaning solution: 4 tablespoons baking soda, 1 teaspoon liquid dish soap and 4 cups water.
• Windex is not recommended as it may break-down silicone and RainX may cause wipers to “chatter”.
1. Mount heated wiper blade assembly using adapters supplied or adapters saved from previous wipers.
2. Run black wires down the UNDER side of wiper arms to base, leaving a small loop for arm action.
3. Allow wipers to flex —DO NOT pull wires tight.
4. Secure wires to wiper arms with black plastic ties.
5. Run remaining wires under the hood.
6. Attach hook connectors to GOOD ground.
7. Hook remaining wires to mating connectors.
8. Test wiper heat by turning "ON" the engine and lighted wiper blade heater switch.
9. NOTE: Blades should feel warm to the touch in a few minutes.
10. Sing or hum "I Can See Clearly Now" by Johnny Nash.
• If no heat in a few minutes, check fuses and connections.
• Make sure both grounds are GOOD.
• If you are operating in a high salt environment, it is a good idea to silicone the ends of the wipers to prevent salt from getting inside the wiper and corroding the splice connectors inside the squeegee.
• We can usually accommodate special applications.
• Blade lengths from 12 inches to 28 inches
• Available for most Foreign and Domestic Cars, Trucks and Buses.
For curved or flat windshields on some heavy duty trucks and some buses. (Mounts to wiper arm with a little screw and nut.) 12″, 14″, 15″, 16″, 18″ & 20″ lengths!
BEGIN INSTALLATION
1. Mount illuminated on/off switch in convenient dash or under-dash location.
2. Hook blue wire to GOOD ground.
3. Attach red wire to a switched circuit.
NOTE: A "switched" circuit is one that is OFF when the ignition is OFF. For example, if your switch is lit with the ignition OFF, the attachment is wrong.
4. Turn wiper switch and ignition "ON".
5. Check that the switch light is "ON" = system connected properly. NOTE: Power will be supplied to the heater elements only when the switch light is "ON".
6. Run black wire from switch through firewall of vehicle and secure wires.
NOTE: You have the option of running around the firewall.
• Remove existing wiper blade assemblies from wiper arms. NOTE: Keep old adapters until Everblades® are installed - they may be useful!
• Clean the windshield completely.
• Recommended cleaning solution: 4 tablespoons baking soda, 1 teaspoon liquid dish soap and 4 cups water.
• Windex is not recommended as it may break-down silicone and RainX may cause wipers to “chatter”.
1. Mount heated wiper blade assembly using adapters supplied or adapters saved from previous wipers.
2. Run black wires down the UNDER side of wiper arms to base, leaving a small loop for arm action.
3. Allow wipers to flex —DO NOT pull wires tight.
4. Secure wires to wiper arms with black plastic ties.
5. Run remaining wires under the hood.
6. Attach hook connectors to GOOD ground.
7. Hook remaining wires to mating connectors.
8. Test wiper heat by turning "ON" the engine and lighted wiper blade heater switch.
9. NOTE: Blades should feel warm to the touch in a few minutes.
10. Sing or hum "I Can See Clearly Now" by Johnny Nash.
• If no heat in a few minutes, check fuses and connections.
• Make sure both grounds are GOOD.
• If you are operating in a high salt environment, it is a good idea to silicone the ends of the wipers to prevent salt from getting inside the wiper and corroding the splice connectors inside the squeegee.
• We can usually accommodate special applications.
• Blade lengths from 12 inches to 28 inches
• Available for most Foreign and Domestic Cars, Trucks and Buses.